search

Directed-audio XTR5002 User Manual Page 4

  • Download
  • Add to my manuals
  • Print
  • Page
    / 100
  • Table of contents
  • TROUBLESHOOTING
    •
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 3
© 2008 Directed Electronics. All rights reserved. 3
END PANEL LAYOUTS
XTR2502
1 2
3
4 5
6
10
9
8
7
1 2
3
4 5
6
9
8
7
HI
LO W
HI
LO W
ON
OFF
+
_
L CH
+
_
R CH
MIN MAX
GAIN
SUB SONIC
R
INPUT
R
OUTPUT
L L
BASS
BOOST
X - OVER
FULL
LPF HPF
0dB 18dB
50
HZ
2K
HZ
ON
OFF
+
+
_
L CH
_
R CH
MIN MAX
GAIN
SUB SONIC
R
INPUT
R
OUTPUT
L L
X - OVER
FULL
LPF HPF
50
HZ
2K
HZ
XTR5002
1 2
3
4 5
6
10
9
8
7
1 2
3
4 5
6
9
8
7
HI
LO W
HI
LO W
ON
OFF
+
_
L CH
+
_
R CH
MIN MAX
GAIN
SUB SONIC
R
INPUT
R
OUTPUT
L L
BASS
BOOST
X - OVER
FULL
LPF HPF
0dB 18dB
50
HZ
2K
HZ
ON
OFF
+
+
_
L CH
_
R CH
MIN MAX
GAIN
SUB SONIC
R
INPUT
R
OUTPUT
L L
X - OVER
FULL
LPF HPF
50
HZ
2K
HZ
Speakers - 1. Left channel
Gain Control- 2. continuous adjustment for full power output
Input Mode - 3. when the switch is out, the amplifier will accept
speaker level and high output RCA connections. When this switch
is in, it provides extra sensitivity for lower input voltage RCA
(refer to item 4 below)
RCA Input - 4. accepts Low Level RCA Inputs (400mV-8V) from a
head unit, preamplifier, or equalizer. XTR amplifiers can also
accepts High Level Speaker Inputs (200mV-4V) from an OEM
stereo. These inputs are configured by the Input Mode switch
position (refer to item 3 above)
RCA Line Output - 5. provides easy connection to additional ampli-
fiers. Note that some OEM stereo headunits may sense the
attached load and may turn off their speaker outputs if expected
load conditions aren’t achieved
X-Over Frequency Control (Flat / All Pass output)- 6. adjusts the
frequency (50Hz–2000Hz) of the crossover for the HPF (High-Pass
Frequency Control) and the LPF (Low-Pass Frequency Control)
X-Over (cross-over) - 7. activates LPF (low pass crossover), FLAT (all
pass), or HPF (high pass crossover)
Speakers - 8. Right channel
Infrasonic (Subsonic) Switch - 9. when On, this cuts off extremely
low bass frequencies (below the range of human hearing, that
speakers cannot effectively reproduce). A high pass filter is
engaged when the Sub Sonic switch is On. This improves efficien-
cy of the amplifier’s power supply, improves sound reproductive
performance, and reduces chances of damaging the subwoofers.
The Subsonic filter is 12dB/Octave @ 24Hz
Bass Boost Rear - 10. continuously adjusts from 0 to 18dB of boost
centered at 45Hz. Only available on the XTR5002
Figure 1
Figura 1
Abbildung 1
Figure 2
Figura 2
Abbildung 2
Page view 3
1 2 3 4 5 6 7 8 9 ... 99 100

Comments to this Manuals

No comments
  • Copland Xaoc-devices Azden ServComp Videotek
  • Speco Audio amplifiers Finlux LCD TVs Fellowes Unknown Phoenix Gold Car audio amplifiers Coleman Power generators
  • Canon Speedlite 470EX-AI MINOLTA-QMS PagePro 9100 Bauknecht CTAC 6740FS NE Sony NW-ZX2 Parrot 3400
  • Sony DAV-DZ340 User Manual Asus V2Je User Manual Emerson Liebert ICOM-DO Installation Manual Panasonic WJ-GXE100 Installation Guide